Walli Roller Shutter

User manuals:

Operating manual – English

Instrukcja obsługi – Polski

Short manual – Multilanguage

Declaration of conformity:

FGWREU-111.pdf

FIBARO Walli Roller Shutter is a smart wall switch designed to control motors of roller blinds, awnings, venetian blinds and other single phase, AC powered devices via Z-Wave network.

It measures active power and energy consumed by the controlled load.

You can install it with provided cover plate and switch button or other compatible.

• Can be used with:
  • roller blinds ,
  • venetian blinds,
  • awnings,
  • blind motors with electronic or mechanical limit switches.
• Can be used with FIBARO Walli covers or other compatible:
  • GIRA – System 55 (Standard 55, E2, Event, Event Clear),
  • Legrand – Céliane,
  • Schneider – Odace.
• Active power and energy metering.
• Supports Z-Wave network Security Modes: S0 with AES-128 encryption and S2 Authenticated with PRNG-based encryption.
• Works as a Z-Wave signal repeater (all non-battery operated devices within the network will act as repeaters to increase reliability of the network).
• May be used with all devices certified with the Z-Wave Plus certificate and should be compatible with such devices produced by other manufacturers.

Read this manual before attempting to install the device!

Failure to observe recommendations included in this manual may be dangerous or cause a violation of the law. The manufacturer, Fibar Group S.A. will not be held responsible for any loss or damage resulting from not following the instructions of operating manual.

• DANGER OF ELECTROCUTION!
  • The device is designed to operate in electrical home installation. Faulty connection or use may result in fire or electric shock.
  • All works on the device may be performed only by a qualified and licensed electrician. Observe national regulations.
  • Even when the device is turned off, voltage may be present at its terminals. Any maintenance introducing changes into the configuration of connections or the load must be always performed with disabled fuse.
  • To avoid risk of electrical shock, do not operate the device with wet or moist hands.
• Do not modify!
  Do not modify this device in any way not included in this manual.
• Other devices
  The manufacturer, Fibar Group S.A. will not be held responsible for any damage or loss of warranty privileges for other connected devices if the connection is not compliant with their manuals.
• This product is intended for indoor use only in dry locations.
  Do not use in damp or wet locations, near a bathtub, sink, shower, swimming pool, or anywhere else where water or moisture are present.
• Caution!
  It is not recommended to operate all of the roller blinds simultaneously. For safety reasons, at least one roller blind should be controlled independently, providing safe escape route in case of emergency.
  
• Not a toy!
  This product is not a toy. Keep away from children and animals!

Connecting the device in a manner inconsistent with this manual may cause risk to health, life or material damage.

• Do not power the device before fully assembling it in the mounting box,
• Connect only in accordance with one of the diagrams,
• Install only in flush mounting boxes compliant with a relevant national safety standards and with depth no less than 40mm,
• Do not connect devices which are not compliant with the specification or relevant safety standards,
• Do not connect heating devices,
• Do not connect SELV or PELV circuits.
• Make sure you have all required parts when installing with covers other than FIBARO.

Device parts:

1 – switch button, 2 – cover plate, 3 – unit (device), 4 – mounting frame

Notes for diagrams:

N – terminal for neutral wire

Q1 – 1st output terminal motor

Q2 – 2nd output terminal motor

L – terminal for live wire

G – groove used to measure wire length

Prepare wires by removing 11.5-13mm of insulation from their ends. You can use groove on the side of the unit to measure the length.

When installing with FIBARO or GIRA covers:

1. Pull out the switch button.
2. Take off the cover plate.

When installing with Legrand or Schneider covers:

1. Pull out the original switch button.
2. Take off the original cover plate.
3. Dismount the original mounting frame.
4. Snap the new mounting frame*.

* Additional mounting frames are sold separately.

1. Switch off the mains voltage (disable the fuse).
2. Connect with the diagram:

   

   Diagram 1: Example connection with roller blind motor

3. Verify correctness of connection.
4. Tighten the terminal screws using PH1 screwdriver.

When installing with FIBARO covers:

If you have unit only: buy Switch Button with Lightguide (FG-WDSEU221-AS-8100) and Mounting Frame FIBARO/GIRA (FG-Wx-AS-4001).

1. Insert the device with mounting frame into the mounting box and secure with mounting claws and screws.
2. Snap the cover plate to the device.
3. Snap the switch button to the device.

When installing with GIRA covers:

1. Insert the device with mounting frame into the mounting box and secure with mounting claws and screws.
2. Snap the new cover plate to the device.
3. Snap the switch button adapter* to the device.
4. Snap the new switch button to the device.

When installing with Legrand covers:

1. Insert the device with mounting frame* into the mounting box and secure with mounting claws and screws.
2. Snap the switch button adapter* to the device.
3. Snap the new inner cover plate to the device.
4. Snap the new outer cover plate to the device.
5. Snap the new switch button to the device.

When installing with Schneider covers:

1. Insert the device with mounting frame* into the mounting box and secure with mounting claws and screws.
2. Snap the new cover plate to the device.
3. Snap the new switch button to the device.

When installing with FIBARO double and triple covers:

Switch buttons, lightguides and mounting frames are necessary to install double and triple cover plates.

• If you have complete FGWREU-111: push the lightguide out through the single Cover Plate and use included switch button and mounting frame.
• If you have unit only: buy Switch Button with Lightguide (FG-WDSEU221-AS-8100) and Mounting Frame FIBARO/GIRA (FG-Wx-AS-4001) for every unit.

1. Press in the lightguides into the cover plate (plastic latches should align).
2. Insert the units with mounting frames into the mounting boxes and secure them with mounting claws and screws.
3. Snap the cover plate.
4. Snap the switch buttons.

* Switch button adapter and additional mounting frames are sold separately.

1. If the device fully assembled, switch on the mains voltage.
2. LED ring light means the device is powered and can be added to the Z-Wave network.

Parts required for Gira System 55 (only with non-metalised outer surface: Standard 55, E2, Event, Event Clear) covers

Parts required for Legrand Céliane covers

Parts required for Schneider Odace covers

Adding (Inclusion) – Z-Wave device learning mode, allowing to add the device to existing Z-Wave network.

Adding manually

To add the device to the Z-Wave network manually:

Adding using SmartStart

SmartStart enabled products can be added into a Z-Wave network by scanning the Z-Wave QR Code present on the product with a controller providing SmartStart inclusion. SmartStart product will be added automatically within 10 minutes of being switched on in the network range.

To add the device to the Z-Wave network using SmartStart:

1. To use SmartStart your controller needs to support Security S2 (see the controller’s manual).
2. Enter the full DSK string code to your controller. If your controller is capable of QR scanning, scan the QR code placed on the label on the bottom of the box.
3. Power the device.
4. Wait for the adding process to start (up to few minutes), which is signalled with yellow LED blinking.
5. Adding result will be confirmed by the Z-Wave controller’s message and the LED frame:
   • Green – successful (non-secure, S0, S2 non-authenticated),
   • Magenta – successful (Security S2 Authenticated),
   • Red – not successful.

Removing (Exclusion) – Z-Wave device learning mode, allowing to remove the device from existing Z-Wave network. Removing also results in resetting the device to factory defaults.

To remove the device from the Z-Wave network:

Calibration is a process during which a device learns the position of the limit switches and a motor characteristic.

Calibration is mandatory in order for the device to correctly recognize a roller blind position.

The procedure consists of an automatic, full movement between the limit switches (up, down, and up again).

Button description:

 – 1st button, for up movement

 – 2nd button, for down movement

Automatic positioning of standard roller blind using the menu

1. Set parameter 151 to 1 (default).
2. Quickly, three times click, then press and hold one of the buttons to enter the menu.
3. Release button when the device glows white.
4. Quickly click the button to confirm.
5. The device will perform the calibration process, completing full cycle – up, down and up again. During the calibration the LED frame blinks white.
6. Test whether the positioning works correctly.

Automatic positioning of standard roller blind using the parameter

1. Set parameter 151 to 1 (default).
2. Set parameter 150 to 2.
3. The device will perform the calibration process, completing full cycle – up, down and up again. During the calibration the LED frame blinks white.
4. Test whether the positioning works correctly.

Manual positioning of slats in venetian blinds mode

1. Set parameter 151 to 2.
2. Calibrate blinds as standard ones (described above).
3. By default, time of transition between extreme positions is set to 150 (1.5 seconds) in parameter 152.
4. Turn slats between extreme positions by holding  or  button:
   • If after full cycle a blind starts moving up or down – decrease value of parameter 152,
   • If after full cycle the slats does not reach end positions – increase value of parameter 152,
5. Repeat previous step until satisfactory positioning is achieved.
6. Test whether the positioning works correctly. Correctly configured slats should not force the blinds to move up or down.

Manual positioning of roller blind with built-in driver

1. Set parameter 151 to 5 or 6.
2. By default, time of transition between extreme positions is set to 6000 (60 seconds) in parameters 156 and 157.
3. Move roller blinds between extreme positions by clicking  or  switch:
   • If roller blind stops before reaching top – increase value of parameter 156,
   • If roller blind does not stop after reaching top – decrease value of parameter 156,
   • If roller blind stops before reaching bottom – increase value of parameter 157,
   • If roller blind does not stop after reaching bottom – decrease value of parameter 157,
4. Repeat previous step until satisfactory positioning is achieved.
5. Test whether the positioning works correctly.

Operating roller blinds (configurable using parameter 24)

• Click  – initiate up movement.
• Click  – initiate down movement.

If the blind is moving, clicking any button, will stop the movement.

Operating slats of venetian blinds

• Hold  – initiate slats rotation up.
• Hold  – initiate slats rotation down.

Release to stop the movement.

Other actions

Perform following actions on one of the buttons to:

• 3xClick – start learn mode to add/remove to/from Z-Wave network,
• 1,2,3xClick/hold/release – activate scene in the controller for specific action (requires configuration using parameters 40 and 41)
• 3xClick then press and hold – enter the menu.

The built-in LED light shows current device status.

After powering the device:

• Green – device added to a Z-Wave network (non-secure, S0, S2 non-authenticated),
• Magenta – device added to a Z-Wave network (Security S2 Authenticated),
• Red – device not added to a Z-Wave network.

State of the device:

• White – load turned ON (configurable using parameters 11 and 12).

Update:

• Blinking cyan – update in progress,
• Green – update successful,
• Red – update not successful.

Menu:

• Blinking green – entering the menu (added as non-secure, S0, S2 non-authenticated),
• Blinking magenta – entering the menu (added as Security S2 Authenticated),
• Blinking red – entering the menu (not added to a Z-Wave network),
• White – start calibration,
• Green – reset energy consumption memory,
• Yellow – reset to factory defaults.

Menu allows to perform Z-Wave network actions. In order to use the menu:

1. Quickly, three times click, then press and hold one of the buttons to enter the menu, device blinks to signal adding status (see: Visual indications).
2. Release the button when device signals desired position with colour:
   • WHITE – start calibration
   • GREEN – reset energy consumption memory
   • MAGENTA – start range test
   • YELLOW – reset to factory defaults
3. Quickly click the button to confirm.

Reset procedure allows to restore the device back to its factory settings, which means all information about the Z-Wave controller and user configuration will be deleted. Resetting to factory defaults does not reset energy consumption memory.

1. Quickly, three times click, then press and hold one of the buttons to enter the menu.
2. Release button when the device glows yellow.
3. Quickly click the button to confirm.
4. After few seconds the device will be restarted, which is signalled with red LED colour.

The device allows for the active power and energy consumption monitoring. Data is sent to the main Z-Wave controller, e.g. Home Center.

Measuring is carried out by the most advanced microcontroller technology, assuring maximum accuracy and precision (+/- 1% for loads greater than 10W).

Electric active power – power that energy receiver is changing into a work or a heat. The unit of active power is Watt [W].

Electric energy – energy consumed by a device through a time period. Consumers of electricity in households are billed by suppliers on the basis of active power used in given unit of time. Most commonly measured in kilowatt-hour [kWh]. One kilowatt-hour is equal to one kilowatt of power consumed over period of one hour,
1kWh = 1000Wh.

Resetting consumption memory:

1. Quickly, three times click, then press and hold one of the buttons to enter the menu.
2. Release button when the device glows green.
3. Quickly click the button to confirm.
4. Device will blink two times green to confirm.

Association (linking devices) – direct control of other devices within the Z-Wave system network.

Associations allow:

• reporting the device status to the Z-Wave controller (using Lifeline group),
• creating simple automations by controlling other devices without participation of the main controller (using groups assigned to actions on the device)

The device provides the association of 3 groups:

1st association group – “Lifeline” reports the device status and allows for assigning single device only (main controller by default).

2nd association group – “Roller Shutter” is assigned to shutter position control – UP/DOWN (uses Switch Multilevel command class).

3rd association group – “Slats” is assigned to slats position control – UP/DOWN (uses Switch Multilevel command class).

The device allows to control 5 regular or multichannel devices per an association group, with the exception of “LifeLine” that is reserved solely for the controller and hence only 1 node can be assigned.

The device allows customizing its operation to user’s needs using configurable parameters.
The settings can be adjusted via the Z-Wave controller to which the device is added. The way of adjusting them might differ depending on the controller.
In the FIBARO interface parameters are presented as simple options in the Advanced Settings of the device.

Available parameters: