Connection with 3-wire 0-10V sensor

You can connect up to 2 analog sensors IN1/IN2 terminals.

  1. Disconnect power.
  2. Connect with the diagram below:

    Diagram 6: Example connection with 3-wire analog sensor to IN1 input (1 – 3-wire analog sensor).
  3. Verify correctness of connection.
  4. Power the device.
  5. Add the device to the Z-Wave network.
  6. Change values of parameters:
    • Connected to IN1: change parameter 20 to 4
    • Connected to IN2: change parameter 21 to 4

Back To Top

Advanced parameters

The device allows to customize its operation to user’s needs using configurable parameters. The settings can be adjusted via Z-Wave controller to which the device is added. The way of adjusting them might differ depending on the controller. In the FIBARO interface parameters are presented as simple options in Advanced Settings of the device.

Parameters dependency
Many of the parameters are relevant only for specific input operating modes (parameters 20 and 21), consult the table below:

Parameter 20 No. 40 No. 47 No. 49 No. 150 No. 152 No. 63 No. 64
0 or 1
2 or 3
4 or 5
Parameter 21 No. 41 No. 52 No. 54 No. 151 No. 153 No. 63 No. 64
0 or 1
2 or 3
4 or 5

 

This parameter allows to choose mode of 1st input (IN1). Change it depending on connected device.
Parameter size: 1B
Default value: 2 (monostable button)

Available values:
0 – Normally closed alarm input (Notification)
1 – Normally open alarm input (Notification)
2 – Monostable button (Central Scene)
3 – Bistable button (Central Scene)
4 – Analog input without internal pull-up (Sensor Multilevel)
5 – Analog input with internal pull-up (Sensor Multilevel)

This parameter allows to choose mode of 2nd input (IN2). Change it depending on connected device.
Parameter size: 1B
Default value: 2 (monostable button)

Available values:
0 – Normally closed alarm input (Notification CC)
1 – Normally open alarm input (Notification CC)
2 – Monostable button (Central Scene CC)
3 – Bistable button (Central Scene CC)
4 – Analog input without internal pull-up (Sensor Multilevel CC)
5 – Analog input with internal pull-up (Sensor Multilevel CC)

This parameter allows reversing operation of IN1 and IN2 inputs without changing the wiring. Use in case of incorrect wiring.
Parameter size: 1B
Default value: 0 (default)

Available values:
0 – default (IN1 – 1st input, IN2 – 2nd input)
1 – reversed (IN1 – 2nd input, IN2 – 1st input)

This parameter allows reversing operation of OUT1 and OUT2 inputs without changing the wiring. Use in case of incorrect wiring.
Parameter size: 1B
Default value: 0 (default)

Available values:
0 – default (OUT1 – 1st output, OUT2 – 2nd output)
1 – reversed (OUT1 – 2nd output, OUT2 – 1st output)

This parameter defines which actions result in sending scene ID and attribute assigned to them (see Activating scenes).
Parameter size: 1B
Default value: 0 (no scenes sent)

Available values:
1 – Key pressed 1 time
2 – Key pressed 2 times
4 – Key pressed 3 times
8 – Key hold down and key released

This parameter defines which actions result in sending scene ID and attribute assigned to them (see Activating scenes). Parameter is relevant only if parameter 21 is set to 2 or 3.
Parameter size: 1B
Default value: 0 (no scenes sent)

Available values:
1 – Key pressed 1 time
2 – Key pressed 2 times
4 – Key pressed 3 times
8 – Key hold down and key released

This parameter defines value sent to devices in 2nd association group when IN1 input is triggered (using Basic Command Class). Parameter is relevant only if parameter 20 is set to 0 or 1 (alarm mode).
Parameter size: 2B
Default value: 255

Available values: 0-255

This parameter defines value sent to devices in 2nd association group when IN1 input is deactivated (using Basic Command Class). Parameter is relevant only if parameter 20 is set to 0 or 1 (alarm mode).
Parameter size: 2B
Default value: 0

Available values: 0-255

This parameter defines value sent to devices in 3rd association group when IN2 input is triggered (using Basic Command Class). Parameter is relevant only if parameter 21 is set to 0 or 1 (alarm mode).
Parameter size: 2B
Default value: 255

Available values: 0-255

This parameter defines value sent to devices in 3rd association group when IN2 input is deactivated (using Basic Command Class). Parameter is relevant only if parameter 21 is set to 0 or 1 (alarm mode).
Parameter size: 2B
Default value: 0

Available values: 0-255

This parameter defines the inertia time of IN1 input in alarm modes. Adjust this parameter to prevent bouncing or signal disruptions. Parameter is relevant only if parameter 20 is set to 0 or 1 (alarm mode).
Parameter size: 1B
Default value: 10 (100ms)

Available values: 1-100 (10ms-1000ms, 10ms step)

This parameter defines the inertia time of IN2 input in alarm modes. Adjust this parameter to prevent bouncing or signal disruptions. Parameter is relevant only if parameter 21 is set to 0 or 1 (alarm mode).
Parameter size: 1B
Default value: 10 (100ms)

Available values: 1-100 (10ms-1000ms, 10ms step)

This parameter defines additional delay of cancelling the alarm on IN1 input. Parameter is relevant only if parameter 20 is set to 0 or 1 (alarm mode).
Parameter size: 2B

Default value: 0 (no delay)

Available values:
0 – no delay
1-3600s

This parameter defines additional delay of cancelling the alarm on IN2 input. Parameter is relevant only if parameter 21 is set to 0 or 1 (alarm mode).
Parameter size: 2B
Default value: 0 (no delay)
Available values:
0 – no delay
0-3600s
This parameter defines logic of OUT1 output operation.
Parameter size: 1B
Default value: 0 (NO)

Available values:
0 – contacts normally open / closed when active
1 – contacts normally closed / open when active

This parameter defines logic of OUT2 output operation.
Parameter size: 1B
Default value: 0 (NO)

Available values:
0 – contacts normally open / closed when active
1 – contacts normally closed / open when active

This parameter defines time after which OUT1 will be automatically deactivated.
Parameter size: 2B
Default value: 0 (auto off disabled)

Available values:
0 – auto off disabled
1-27000 (0.1s-45min, 0.1s step)

This parameter defines time after which OUT2 will be automatically deactivated.
Parameter size: 2B
Default value: 0 (auto off disabled)

Available values:
0 – auto off disabled
1-27000 (0.1s-45min, 0.1s step)

This parameter defines minimal change (from the last reported) of analog input value that results in sending new report. Parameter is relevant only for analog inputs (parameter 20 or 21 set to 4 or 5).
Parameter size: 1B
Default value: 5 (0.5V)

Available values:
0 – reporting on change disabled
1-100 (0.1-10V, 0.1V step)

This parameter defines reporting period of analog inputs value. Periodical reports are independent from changes in value (parameter 63). Parameter is relevant only for analog inputs (parameter 20 or 21 set to 4 or 5).
Parameter size: 2B
Default value: 0 (periodical reports disabled)

Available values:
0 – periodical reports disabled
60-32400 (60s-9h, 1s step)

This parameter defines minimal change (from the last reported) of internal temperature sensor value that results in sending new report.
Parameter size: 2B
Default value: 5 (0.5°C)

Available values:
0 – reporting on change disabled
1-255 (0.1-25.0°C, 0.1°C step )

This parameter defines reporting period of internal temperature sensor value. Periodical reports are independent from changes in value (parameter 65).
Parameter size: 2B
Default value: 0 (periodical reports disabled)

Available values:
0 – periodical reports disabled
60-32400 (60s-9h, 1s step)

This parameter defines minimal change (from the last reported) of external sensors values (DS18B20 or DHT22) that results in sending new report. Parameter is relevant only for connected DS18B20 or DHT22 sensors.
Parameter size: 2B
Default value: 5 (0.5 units)

Available values:
0 – reporting on change disabled
1-255 (0.1-25.5 units, 0.1 unit step)

This parameter defines reporting period of analog inputs value. Periodical reports are independent from changes in value (parameter 67). Parameter is relevant only for connected DS18B20 or DHT22 sensors.
Parameter size: 2B
Default value: 0 (periodical reports disabled)

Available values:
0 – periodical reports disabled
60-32400 (60s-9h, 1s step)


Back To Top

Associations

Association (linking devices) – direct control of other devices within the Z-Wave system network e.g. Dimmer, Relay Switch, Roller Shutter or scene (may be controlled only through a Z-Wave controller).

Association ensures direct transfer of control commands between devices, is performed without participation of the main controller and requires associated device to be in the direct range.

The device provides the association of 3 groups:

1st association group – “Lifeline” reports the device status and allows for assigning single device only (main controller by default).

2nd association group – “On/Off (IN1)” is assigned to IN1 input terminal (uses Basic command class).

3rd association group – “On/Off (IN2)” is assigned to IN2 input terminal (uses Basic command class).

The device in 2nd and 3rd group allows to control 5 regular or multichannel devices per an association group, with the exception of
LifeLine that is reserved solely for the controller and hence only 1 node can be assigned.

Back To Top

Activating scenes

The device can activate scenes in the Z-Wave controller by sending scene ID and attribute of a specific action using Central Scene Command Class.

In order for this functionality to work connect monostable or bistable switch to the IN1 or IN2 input and set parameter 20 (IN1) or 21 (IN2) to 2 or 3.

By default scenes are not activated, set parameters 40 and 41 to enable scene activation for selected actions.

Switch connected to IN1 terminal:

Action Scene ID Attribute
Switch clicked once 1 Key Pressed 1 time
Switch clicked twice 1 Key Pressed 2 times
Switch clicked thrice * 1 Key Pressed 3 times
Switch held** 1 Key Held Down
Switch released** 1 Key Released

Switch connected to IN2 terminal:

Action Scene ID Attribute
Switch clicked once 2 Key Pressed 1 time
Switch clicked twice 2 Key Pressed 2 times
Switch clicked thrice * 2 Key Pressed 3 times
Switch held** 2 Key Held Down
Switch released** 2 Key Released

* Activating triple clicks will disallow removing using input terminal.

** Not available for toggle switches.

Back To Top

Z-Wave range test

The device has a built in Z-Wave network main controller’s range tester.

To make Z-Wave range test possible, the device must be added to the Z-Wave controller. Testing may stress the network, so it is recommended to perform the test only in special cases.

To test the main controller’s range:

  1. Press and hold the button to enter the menu.
  2. Release button when the device glows magenta.
  3. Quickly click the button to confirm.
  4. Visual indicator will indicate the Z-Wave network’s range (range signaling modes described below).
  5. To exit Z-Wave range test, press the button briefly.

Z-Wave range tester signalling modes:

  • Visual indicator pulsing green – the device attempts to establish a direct communication with the main controller. If a direct communication attempt fails, the device will try to establish a routed communication, through other modules, which will be signalled by visual indicator pulsing yellow.
  • Visual indicator glowing green – the device communicates with the main controller directly.
  • Visual indicator pulsing yellow – the device tries to establish a routed communication with the main controller through other modules (repeaters).
  • Visual indicator glowing yellow – the device communicates with the main controller through the other modules. After 2 seconds the device will retry to establish a direct communication with the main controller, which will be signalled with visual indicator pulsing green.
  • Visual indicator pulsing violet – the device does communicate at the maximum distance of the Z-Wave network. If connection proves successful it will be confirmed with a yellow glow. It’s not recommended to use the device at the range limit.
  • Visual indicator glowing red – the device is not able to connect to the main controller directly or through another Z-Wave network device (repeater).

Communication mode of the device may switch between direct and one using routing, especially if the device is on the limit of the direct range.

Back To Top

Testing operation

The built-in button allows to test device operation as follows:

  • 1x click button – switch OUT1 output
  • 2x click button – switch OUT2 output

Back To Top

Resetting to factory defaults

Reset procedure allows to restore the device back to its factory settings, which means all information about the Z-Wave controller and user configuration will be deleted.

Resetting the device is not the recommended way of removing the device from the Z-Wave network. Use reset procedure only if the primary controller is missing or inoperable. Certain device removal can be achieved by the procedure of removing described.

  1. Press and hold the button to enter the menu.
  2. Release button when the device glows yellow.
  3. Quickly click the button to confirm.
  4. After few seconds the device will be restarted, which is signalled with the red colour.

Back To Top

Menu

Menu allows to perform Z-Wave network actions. In order to use the menu:

  1. Press and hold the button to enter the menu, device blinks to signal adding status (see 7.1: Visual indications).
  2. Release the button when device signals desired position with colour:
    • MAGENTA – start range test
    • YELLOW – reset the device
  3. Quickly click the button to confirm.

Back To Top